[nflug] hardware issue

[Justin Bennett]

Ok, I had a few old penguin computing boxes that had only on proc. in a 
dual board, I'll see if I can track it down.

Justin Bennett
Network Administrator
Dynabrade, Inc.
8989 Sheridan Dr.
Clarence, NY 14031
 



On 2/16/2006 2:57 PM, Frank Kumro wrote:

>yea the old P3 style, wierd type if u ask me.
>
>On 2/16/06, Justin Bennett <Justin.Bennett at dynabrade.com> wrote:
>  
>
>>Slot 1 is the old PIII style? I might have one in the back in an old server.
>>
>>Justin Bennett
>>Network Administrator
>>Dynabrade, Inc.
>>8989 Sheridan Dr.
>>Clarence, NY 14031
>>
>>
>>
>>
>>On 2/16/2006 2:42 PM, Frank Kumro wrote:
>>
>>    
>>
>>>does anyone have a slot 1 termination card that I could possibly use
>>>because to run a single processor I need one of those cards. Or if
>>>anyone would like to make a couple bucks and sell me one...either way
>>>i need one. I tested the memory and its fine the only thing plugged in
>>>is
>>>Ram,
>>>Both Proc,
>>>and of course power supply
>>>
>>>yet it still wont enter the setup when i press f2...still says
>>>entering setup but no go
>>>
>>>On 2/15/06, Frank Kumro <fkumro at gmail.com> wrote:
>>>
>>>
>>>      
>>>
>>>>I will try these options tomorrow when I have some free time. Thanks again!
>>>>
>>>>On 2/15/06, may pre house the seamy side volitation <wpos2 at adelphia.net> wrote:
>>>>
>>>>
>>>>        
>>>>
>>>>>I would try switching the processor slots.  The only reason that I can
>>>>>think for this is that maybe the resistance in one of the pins of one of
>>>>>the processors, however minute, is just enough in the MB circuitry to
>>>>>throw it off.  Switching them around may put that pin on a more friendly
>>>>>circuit.
>>>>>
>>>>>Forgive my ignorance of dual-proc setups, but can you run just one
>>>>>processor?  If you have the ability of trying each processor in each
>>>>>slot, then the results may tell you something.
>>>>>
>>>>>Then of course there's the old adage of starting with the bare basics
>>>>>and adding stuff (I'm thinking of the SCSI card) until the system fails.
>>>>>
>>>>>Użytkownik Frank Kumro napisał:
>>>>>
>>>>>
>>>>>          
>>>>>
>>>>>>I just recieved my Intel L440GX+ motherboard and I have two p3
>>>>>>processors for it. The ram, processors and everything else has been
>>>>>>installed and the computer powers on. The intel server screen appears
>>>>>>and i press f2 to enter setup. It says entering setup...thens shows
>>>>>>the adaptec scsi speal then refreshes to a blank screen. Then
>>>>>>nothing...no setup. I cleared the CMOS using the jumpers ... also if I
>>>>>>boot without entering setup it has an error with non matching FSP of
>>>>>>the processors (which are the same and has run in a dual config
>>>>>>before). Any ideas? Im lost and would really like to get this machine
>>>>>>up and running...
>>>>>>
>>>>>>thanks again guys!
>>>>>>
>>>>>>--
>>>>>>Frank
>>>>>>Shenanigans!!
>>>>>>_______________________________________________
>>>>>>nflug mailing list
>>>>>>nflug at nflug.org
>>>>>>http://www.nflug.org/mailman/listinfo/nflug
>>>>>>
>>>>>>
>>>>>>
>>>>>>            
>>>>>>
>>>>>_______________________________________________
>>>>>nflug mailing list
>>>>>nflug at nflug.org
>>>>>http://www.nflug.org/mailman/listinfo/nflug
>>>>>
>>>>>
>>>>>
>>>>>          
>>>>>
>>>>--
>>>>Frank
>>>>Shenanigans!!
>>>>
>>>>
>>>>
>>>>        
>>>>
>>>--
>>>Frank
>>>Shenanigans!!
>>>
>>>
>>>------------------------------------------------------------------------
>>>
>>>_______________________________________________
>>>nflug mailing list
>>>nflug at nflug.org
>>>http://www.nflug.org/mailman/listinfo/nflug
>>>
>>>
>>>      
>>>
>>_______________________________________________
>>nflug mailing list
>>nflug at nflug.org
>>http://www.nflug.org/mailman/listinfo/nflug
>>
>>    
>>
>
>
>--
>Frank
>Shenanigans!!
>  
>
>------------------------------------------------------------------------
>
>_______________________________________________
>nflug mailing list
>nflug at nflug.org
>http://www.nflug.org/mailman/listinfo/nflug
>  
>
_______________________________________________
nflug mailing list
nflug at nflug.org
http://www.nflug.org/mailman/listinfo/nflug