[nflug] hardware issue

[Frank Kumro]

yea the old P3 style, wierd type if u ask me.

On 2/16/06, Justin Bennett <Justin.Bennett at dynabrade.com> wrote:
> Slot 1 is the old PIII style? I might have one in the back in an old server.
>
> Justin Bennett
> Network Administrator
> Dynabrade, Inc.
> 8989 Sheridan Dr.
> Clarence, NY 14031
>
>
>
>
> On 2/16/2006 2:42 PM, Frank Kumro wrote:
>
> >does anyone have a slot 1 termination card that I could possibly use
> >because to run a single processor I need one of those cards. Or if
> >anyone would like to make a couple bucks and sell me one...either way
> >i need one. I tested the memory and its fine the only thing plugged in
> >is
> >Ram,
> >Both Proc,
> >and of course power supply
> >
> >yet it still wont enter the setup when i press f2...still says
> >entering setup but no go
> >
> >On 2/15/06, Frank Kumro <fkumro at gmail.com> wrote:
> >
> >
> >>I will try these options tomorrow when I have some free time. Thanks again!
> >>
> >>On 2/15/06, may pre house the seamy side volitation <wpos2 at adelphia.net> wrote:
> >>
> >>
> >>>I would try switching the processor slots.  The only reason that I can
> >>>think for this is that maybe the resistance in one of the pins of one of
> >>>the processors, however minute, is just enough in the MB circuitry to
> >>>throw it off.  Switching them around may put that pin on a more friendly
> >>>circuit.
> >>>
> >>>Forgive my ignorance of dual-proc setups, but can you run just one
> >>>processor?  If you have the ability of trying each processor in each
> >>>slot, then the results may tell you something.
> >>>
> >>>Then of course there's the old adage of starting with the bare basics
> >>>and adding stuff (I'm thinking of the SCSI card) until the system fails.
> >>>
> >>>Użytkownik Frank Kumro napisał:
> >>>
> >>>
> >>>>I just recieved my Intel L440GX+ motherboard and I have two p3
> >>>>processors for it. The ram, processors and everything else has been
> >>>>installed and the computer powers on. The intel server screen appears
> >>>>and i press f2 to enter setup. It says entering setup...thens shows
> >>>>the adaptec scsi speal then refreshes to a blank screen. Then
> >>>>nothing...no setup. I cleared the CMOS using the jumpers ... also if I
> >>>>boot without entering setup it has an error with non matching FSP of
> >>>>the processors (which are the same and has run in a dual config
> >>>>before). Any ideas? Im lost and would really like to get this machine
> >>>>up and running...
> >>>>
> >>>>thanks again guys!
> >>>>
> >>>>--
> >>>>Frank
> >>>>Shenanigans!!
> >>>>_______________________________________________
> >>>>nflug mailing list
> >>>>nflug at nflug.org
> >>>>http://www.nflug.org/mailman/listinfo/nflug
> >>>>
> >>>>
> >>>>
> >>>_______________________________________________
> >>>nflug mailing list
> >>>nflug at nflug.org
> >>>http://www.nflug.org/mailman/listinfo/nflug
> >>>
> >>>
> >>>
> >>--
> >>Frank
> >>Shenanigans!!
> >>
> >>
> >>
> >
> >
> >--
> >Frank
> >Shenanigans!!
> >
> >
> >------------------------------------------------------------------------
> >
> >_______________________________________________
> >nflug mailing list
> >nflug at nflug.org
> >http://www.nflug.org/mailman/listinfo/nflug
> >
> >
> _______________________________________________
> nflug mailing list
> nflug at nflug.org
> http://www.nflug.org/mailman/listinfo/nflug
>


--
Frank
Shenanigans!!
-------------- next part --------------
_______________________________________________
nflug mailing list
nflug at nflug.org
http://www.nflug.org/mailman/listinfo/nflug