[nflug] hardware issue

[Frank Kumro]

thanks :)

On 2/16/06, Justin Bennett <Justin.Bennett at dynabrade.com> wrote:
> Ok, I had a few old penguin computing boxes that had only on proc. in a
> dual board, I'll see if I can track it down.
>
> Justin Bennett
> Network Administrator
> Dynabrade, Inc.
> 8989 Sheridan Dr.
> Clarence, NY 14031
>
>
>
>
> On 2/16/2006 2:57 PM, Frank Kumro wrote:
>
> >yea the old P3 style, wierd type if u ask me.
> >
> >On 2/16/06, Justin Bennett <Justin.Bennett at dynabrade.com> wrote:
> >
> >
> >>Slot 1 is the old PIII style? I might have one in the back in an old server.
> >>
> >>Justin Bennett
> >>Network Administrator
> >>Dynabrade, Inc.
> >>8989 Sheridan Dr.
> >>Clarence, NY 14031
> >>
> >>
> >>
> >>
> >>On 2/16/2006 2:42 PM, Frank Kumro wrote:
> >>
> >>
> >>
> >>>does anyone have a slot 1 termination card that I could possibly use
> >>>because to run a single processor I need one of those cards. Or if
> >>>anyone would like to make a couple bucks and sell me one...either way
> >>>i need one. I tested the memory and its fine the only thing plugged in
> >>>is
> >>>Ram,
> >>>Both Proc,
> >>>and of course power supply
> >>>
> >>>yet it still wont enter the setup when i press f2...still says
> >>>entering setup but no go
> >>>
> >>>On 2/15/06, Frank Kumro <fkumro at gmail.com> wrote:
> >>>
> >>>
> >>>
> >>>
> >>>>I will try these options tomorrow when I have some free time. Thanks again!
> >>>>
> >>>>On 2/15/06, may pre house the seamy side volitation <wpos2 at adelphia.net> wrote:
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>>I would try switching the processor slots.  The only reason that I can
> >>>>>think for this is that maybe the resistance in one of the pins of one of
> >>>>>the processors, however minute, is just enough in the MB circuitry to
> >>>>>throw it off.  Switching them around may put that pin on a more friendly
> >>>>>circuit.
> >>>>>
> >>>>>Forgive my ignorance of dual-proc setups, but can you run just one
> >>>>>processor?  If you have the ability of trying each processor in each
> >>>>>slot, then the results may tell you something.
> >>>>>
> >>>>>Then of course there's the old adage of starting with the bare basics
> >>>>>and adding stuff (I'm thinking of the SCSI card) until the system fails.
> >>>>>
> >>>>>Użytkownik Frank Kumro napisał:
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>>I just recieved my Intel L440GX+ motherboard and I have two p3
> >>>>>>processors for it. The ram, processors and everything else has been
> >>>>>>installed and the computer powers on. The intel server screen appears
> >>>>>>and i press f2 to enter setup. It says entering setup...thens shows
> >>>>>>the adaptec scsi speal then refreshes to a blank screen. Then
> >>>>>>nothing...no setup. I cleared the CMOS using the jumpers ... also if I
> >>>>>>boot without entering setup it has an error with non matching FSP of
> >>>>>>the processors (which are the same and has run in a dual config
> >>>>>>before). Any ideas? Im lost and would really like to get this machine
> >>>>>>up and running...
> >>>>>>
> >>>>>>thanks again guys!
> >>>>>>
> >>>>>>--
> >>>>>>Frank
> >>>>>>Shenanigans!!
> >>>>>>_______________________________________________
> >>>>>>nflug mailing list
> >>>>>>nflug at nflug.org
> >>>>>>http://www.nflug.org/mailman/listinfo/nflug
> >>>>>>
> >>>>>>
> >>>>>>
> >>>>>>
> >>>>>>
> >>>>>_______________________________________________
> >>>>>nflug mailing list
> >>>>>nflug at nflug.org
> >>>>>http://www.nflug.org/mailman/listinfo/nflug
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>>--
> >>>>Frank
> >>>>Shenanigans!!
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>--
> >>>Frank
> >>>Shenanigans!!
> >>>
> >>>
> >>>------------------------------------------------------------------------
> >>>
> >>>_______________________________________________
> >>>nflug mailing list
> >>>nflug at nflug.org
> >>>http://www.nflug.org/mailman/listinfo/nflug
> >>>
> >>>
> >>>
> >>>
> >>_______________________________________________
> >>nflug mailing list
> >>nflug at nflug.org
> >>http://www.nflug.org/mailman/listinfo/nflug
> >>
> >>
> >>
> >
> >
> >--
> >Frank
> >Shenanigans!!
> >
> >
> >------------------------------------------------------------------------
> >
> >_______________________________________________
> >nflug mailing list
> >nflug at nflug.org
> >http://www.nflug.org/mailman/listinfo/nflug
> >
> >
> _______________________________________________
> nflug mailing list
> nflug at nflug.org
> http://www.nflug.org/mailman/listinfo/nflug
>


--
Frank
Shenanigans!!
-------------- next part --------------
_______________________________________________
nflug mailing list
nflug at nflug.org
http://www.nflug.org/mailman/listinfo/nflug