[nflug] Kubuntu on HP Notebook
Joe
josephj at main.nc.us
Sat Aug 12 02:28:20 EDT 2006
Hi. I've tested most things out in the store using the kubuntu Dapper
Drake CD.
It looks like things are good but there are still a few things in the
system log that don't look right.
I'd really appreciate it if any of you could review this and let me know
if anything looks wrong.
I apologize for the long post. I'm not sure what you might need to see.
I'm looking at two notebooks, an HP and a Toshiba. This email is about
the HP.
TIA
Joe
HP dmesg output:
Stuff that looks "wrong" before the whole log is listed below:
---
[4294667.296000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
---
[4294668.994000] PnPBIOS: Disabled by ACPI PNP
[4294668.994000] PCI: Using ACPI for IRQ routing
[4294668.994000] PCI: If a device doesn't work, try "pci=routeirq". If
it helps, post a report
[4294668.994000] PCI: Cannot allocate resource region 7 of bridge
0000:00:1c.0
[4294668.994000] PCI: Cannot allocate resource region 8 of bridge
0000:00:1c.0
[4294668.994000] PCI: Cannot allocate resource region 7 of bridge
0000:00:1c.1
[4294668.994000] PCI: Cannot allocate resource region 8 of bridge
0000:00:1c.1
[4294668.994000] PCI: Cannot allocate resource region 7 of bridge
0000:00:1c.2
[4294668.994000] PCI: Cannot allocate resource region 8 of bridge
0000:00:1c.2
[4294668.994000] PCI: Cannot allocate resource region 0 of device
0000:06:00.0
[4294669.032000] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[4294669.032000] PCI: Bridge: 0000:00:1c.0
[4294669.032000] IO window: disabled.
[4294669.032000] MEM window: disabled.
[4294669.032000] PREFETCH window: disabled.
[4294669.032000] PCI: Bridge: 0000:00:1c.1
[4294669.032000] IO window: disabled.
[4294669.032000] MEM window: disabled.
[4294669.032000] PREFETCH window: disabled.
[4294669.032000] PCI: Bridge: 0000:00:1c.2
[4294669.032000] IO window: disabled.
[4294669.032000] MEM window: 52000000-520fffff
[4294669.032000] PREFETCH window: disabled.
---
Whole Log:
[4294667.296000] Linux version 2.6.15-23-386 (buildd at rothera) (gcc
version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 PREEMPT Tue May 23 13:49:40
UTC 2006
[4294667.296000] BIOS-provided physical RAM map:
[4294667.296000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[4294667.296000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[4294667.296000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[4294667.296000] BIOS-e820: 0000000000100000 - 000000003f680000 (usable)
[4294667.296000] BIOS-e820: 000000003f680000 - 000000003f700000 (ACPI NVS)
[4294667.296000] BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
[4294667.296000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[4294667.296000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[4294667.296000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
[4294667.296000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[4294667.296000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[4294667.296000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[4294667.296000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[4294667.296000] 118MB HIGHMEM available.
[4294667.296000] 896MB LOWMEM available.
[4294667.296000] found SMP MP-table at 000f65b0
[4294667.296000] On node 0 totalpages: 259712
[4294667.296000] DMA zone: 4096 pages, LIFO batch:0
[4294667.296000] DMA32 zone: 0 pages, LIFO batch:0
[4294667.296000] Normal zone: 225280 pages, LIFO batch:31
[4294667.296000] HighMem zone: 30336 pages, LIFO batch:7
[4294667.296000] DMI present.
[4294667.296000] ACPI: RSDP (v000 PTLTD
) @ 0x000f6580
[4294667.296000] ACPI: RSDT (v001 PTLTD Capell00 0x06040000 LTP
0x00000000) @ 0x3f68be82
[4294667.296000] ACPI: FADT (v001 HP NISSAN 0x06040000 LOHR
0x0000005a) @ 0x3f692dee
[4294667.296000] ACPI: MADT (v001 HP NISSAN 0x06040000 LOHR
0x0000005a) @ 0x3f692e62
[4294667.296000] ACPI: HPET (v001 HP NISSAN 0x06040000 LOHR
0x0000005a) @ 0x3f692eca
[4294667.296000] ACPI: MCFG (v001 HP NISSAN 0x06040000 LOHR
0x0000005a) @ 0x3f692f02
[4294667.296000] ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP
0x00000001) @ 0x3f692fd8
[4294667.296000] ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP
0x00000000) @ 0x3f692f70
[4294667.296000] ACPI: SSDT (v001 SataRe SataAhci 0x00001000 INTL
0x20060217) @ 0x3f68c896
[4294667.296000] ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL
0x20060217) @ 0x3f68bec6
[4294667.296000] ACPI: DSDT (v001 HP NISSAN 0x06040000 INTL
0x20060217) @ 0x00000000
[4294667.296000] ACPI: PM-Timer IO Port: 0x1008
[4294667.296000] ACPI: Local APIC address 0xfee00000
[4294667.296000] ACPI: 2 duplicate APIC table ignored.
[4294667.296000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[4294667.296000] Processor #0 6:14 APIC version 20
[4294667.296000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[4294667.296000] Processor #1 6:14 APIC version 20
[4294667.296000] WARNING: NR_CPUS limit of 1 reached. Processor ignored.
[4294667.296000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[4294667.296000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[4294667.296000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[4294667.296000] IOAPIC[0]: apic_id 1 already used, trying 2
[4294667.296000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000,
GSI 0-23
[4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[4294667.296000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[4294667.296000] ACPI: IRQ0 used by override.
[4294667.296000] ACPI: IRQ2 used by override.
[4294667.296000] ACPI: IRQ9 used by override.
[4294667.296000] Enabling APIC mode: Flat. Using 1 I/O APICs
[4294667.296000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[4294667.296000] Using ACPI (MADT) for SMP configuration information
[4294667.296000] Allocating PCI resources starting at 50000000 (gap:
40000000:a0000000)
[4294667.296000] Built 1 zonelists
[4294667.296000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz
preseed/file=/cdrom/preseed/kubuntu.seed boot=casper
initrd=/casper/initrd.gz ramdisk_size=1048576 root=/dev/ram rw quiet
splash --
[4294667.296000] mapped APIC to ffffd000 (fee00000)
[4294667.296000] mapped IOAPIC to ffffc000 (fec00000)
[4294667.296000] Initializing CPU#0
[4294667.296000] PID hash table entries: 4096 (order: 12, 65536 bytes)
[4294667.296000] Console: colour VGA+ 80x25
[4294667.296000] Dentry cache hash table entries: 131072 (order: 7,
524288 bytes)
[4294667.296000] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes)
[4294667.296000] Memory: 1019028k/1038848k available (1976k kernel code,
19080k reserved, 606k data, 288k init, 121344k highmem)
[4294667.296000] Checking if this processor honours the WP bit even in
supervisor mode... Ok.
[4294667.296000] hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2,
8, 0
[4294667.296000] hpet0: 3 64-bit timers, 14318180 Hz
[4294667.296000] Using HPET for base-timer
[4294667.296000] Using HPET for gettimeofday
[4294667.296000] Detected 1596.122 MHz processor.
[4294667.296000] Using hpet for high-res timesource
[4294667.357000] Calibrating delay using timer specific routine..
3195.53 BogoMIPS (lpj=1597768)
[4294667.357000] Security Framework v1.0.0 initialized
[4294667.357000] SELinux: Disabled at boot.
[4294667.357000] Mount-cache hash table entries: 512
[4294667.357000] CPU: After generic identify, caps: bfe9fbff 00100000
00000000 00000000 0000c189 00000000 00000000
[4294667.357000] CPU: After vendor identify, caps: bfe9fbff 00100000
00000000 00000000 0000c189 00000000 00000000
[4294667.357000] monitor/mwait feature present.
[4294667.357000] using mwait in idle threads.
[4294667.357000] CPU: L1 I cache: 32K, L1 D cache: 32K
[4294667.357000] CPU: L2 cache: 2048K
[4294667.357000] CPU: After all inits, caps: bfe9fbff 00100000 00000000
00000040 0000c189 00000000 00000000
[4294667.357000] mtrr: v2.0 (20020519)
[4294667.357000] CPU: Intel Genuine Intel(R) CPU T2050 @
1.60GHz stepping 08
[4294667.357000] Enabling fast FPU save and restore... done.
[4294667.357000] Enabling unmasked SIMD FPU exception support... done.
[4294667.357000] Checking 'hlt' instruction... OK.
[4294667.361000] checking if image is initramfs... it is
[4294668.728000] Freeing initrd memory: 6836k freed
[4294668.734000] ACPI: Looking for DSDT ... not found!
[4294668.758000] ENABLING IO-APIC IRQs
[4294668.758000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[4294668.870000] NET: Registered protocol family 16
[4294668.870000] EISA bus registered
[4294668.870000] ACPI: bus type pci registered
[4294668.870000] PCI: PCI BIOS revision 2.10 entry at 0xfd873, last bus=9
[4294668.870000] PCI: Using MMCONFIG
[4294668.871000] ACPI: Subsystem revision 20051216
[4294668.875000] ACPI: Interpreter enabled
[4294668.875000] ACPI: Using IOAPIC for interrupt routing
[4294668.876000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[4294668.876000] PCI: Probing PCI hardware (bus 00)
[4294668.899000] Boot video device is 0000:00:02.0
[4294668.900000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[4294668.901000] PCI: Transparent bridge - 0000:00:1e.0
[4294668.901000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[4294668.908000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[4294668.909000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[4294668.909000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[4294668.910000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[4294668.911000] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12
14 15) *11
[4294668.912000] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 *4 5 6 7 11
12 14 15)
[4294668.912000] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10
12 14 15)
[4294668.913000] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12
14 15) *10
[4294668.913000] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 *6 7 10
12 14 15)
[4294668.914000] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12
14 15) *0, disabled.
[4294668.914000] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 *7 10
12 14 15)
[4294668.915000] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 *5 6 7 11
12 14 15)
[4294668.915000] ACPI: Embedded Controller [EC0] (gpe 25) interrupt mode.
[4294668.966000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294668.966000] pnp: PnP ACPI init
[4294668.993000] pnp: PnP ACPI: found 10 devices
[4294668.994000] PnPBIOS: Disabled by ACPI PNP
[4294668.994000] PCI: Using ACPI for IRQ routing
[4294668.994000] PCI: If a device doesn't work, try "pci=routeirq". If
it helps, post a report
[4294668.994000] PCI: Cannot allocate resource region 7 of bridge
0000:00:1c.0
[4294668.994000] PCI: Cannot allocate resource region 8 of bridge
0000:00:1c.0
[4294668.994000] PCI: Cannot allocate resource region 7 of bridge
0000:00:1c.1
[4294668.994000] PCI: Cannot allocate resource region 8 of bridge
0000:00:1c.1
[4294668.994000] PCI: Cannot allocate resource region 7 of bridge
0000:00:1c.2
[4294668.994000] PCI: Cannot allocate resource region 8 of bridge
0000:00:1c.2
[4294668.994000] PCI: Cannot allocate resource region 0 of device
0000:06:00.0
[4294669.032000] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[4294669.032000] PCI: Bridge: 0000:00:1c.0
[4294669.032000] IO window: disabled.
[4294669.032000] MEM window: disabled.
[4294669.032000] PREFETCH window: disabled.
[4294669.032000] PCI: Bridge: 0000:00:1c.1
[4294669.032000] IO window: disabled.
[4294669.032000] MEM window: disabled.
[4294669.032000] PREFETCH window: disabled.
[4294669.032000] PCI: Bridge: 0000:00:1c.2
[4294669.032000] IO window: disabled.
[4294669.032000] MEM window: 52000000-520fffff
[4294669.032000] PREFETCH window: disabled.
[4294669.032000] PCI: Bus 9, cardbus bridge: 0000:08:06.0
[4294669.032000] IO window: 00002400-000024ff
[4294669.032000] IO window: 00002800-000028ff
[4294669.032000] PREFETCH window: 50000000-51ffffff
[4294669.032000] MEM window: 54000000-55ffffff
[4294669.032000] PCI: Bridge: 0000:00:1e.0
[4294669.032000] IO window: 2000-2fff
[4294669.032000] MEM window: d0000000-d00fffff
[4294669.032000] PREFETCH window: 50000000-51ffffff
[4294669.032000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level,
low) -> IRQ 169
[4294669.032000] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[4294669.032000] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level,
low) -> IRQ 177
[4294669.032000] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[4294669.032000] PCI: Enabling device 0000:00:1c.2 (0100 -> 0102)
[4294669.032000] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level,
low) -> IRQ 185
[4294669.032000] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[4294669.032000] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[4294669.032000] ACPI: PCI Interrupt 0000:08:06.0[A] -> GSI 18 (level,
low) -> IRQ 185
[4294669.033000] Simple Boot Flag at 0x36 set to 0x1
[4294669.033000] audit: initializing netlink socket (disabled)
[4294669.033000] audit(1155311396.032:1): initialized
[4294669.033000] highmem bounce pool size: 64 pages
[4294669.033000] VFS: Disk quotas dquot_6.5.1
[4294669.034000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294669.034000] Initializing Cryptographic API
[4294669.034000] io scheduler noop registered
[4294669.034000] io scheduler anticipatory registered
[4294669.034000] io scheduler deadline registered
[4294669.034000] io scheduler cfq registered
[4294674.534000] 0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?)
01010001
[4294674.534000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level,
low) -> IRQ 169
[4294674.534000] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[4294674.534000] assign_interrupt_mode Found MSI capability
[4294674.534000] Allocate Port Service[pcie00]
[4294674.534000] Allocate Port Service[pcie02]
[4294674.534000] Allocate Port Service[pcie03]
[4294674.534000] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level,
low) -> IRQ 177
[4294674.534000] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[4294674.534000] assign_interrupt_mode Found MSI capability
[4294674.534000] Allocate Port Service[pcie00]
[4294674.534000] Allocate Port Service[pcie02]
[4294674.534000] Allocate Port Service[pcie03]
[4294674.534000] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level,
low) -> IRQ 185
[4294674.534000] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[4294674.534000] assign_interrupt_mode Found MSI capability
[4294674.534000] Allocate Port Service[pcie00]
[4294674.535000] Allocate Port Service[pcie02]
[4294674.535000] Allocate Port Service[pcie03]
[4294674.535000] isapnp: Scanning for PnP cards...
[4294674.895000] isapnp: No Plug & Play device found
[4294674.918000] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at
0x60,0x64 irq 1,12
[4294674.935000] i8042.c: Detected active multiplexing controller, rev 1.1.
[4294674.952000] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[4294674.955000] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[4294674.957000] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[4294674.959000] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[4294674.961000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294674.961000] Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports,
IRQ sharing enabled
[4294674.965000] RAMDISK driver initialized: 16 RAM disks of 1048576K
size 1024 blocksize
[4294674.965000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294674.965000] ide: Assuming 33MHz system bus speed for PIO modes;
override with idebus=xx
[4294674.965000] mice: PS/2 mouse device common for all mice
[4294674.969000] EISA: Probing bus 0 at eisa.0
[4294674.969000] Cannot allocate resource for EISA slot 1
[4294674.969000] Cannot allocate resource for EISA slot 2
[4294674.969000] EISA: Detected 0 cards.
[4294674.969000] NET: Registered protocol family 2
[4294674.994000] IP route cache hash table entries: 32768 (order: 5,
131072 bytes)
[4294674.994000] TCP established hash table entries: 131072 (order: 7,
524288 bytes)
[4294675.002000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[4294675.003000] TCP: Hash tables configured (established 131072 bind 65536)
[4294675.003000] TCP reno registered
[4294675.003000] TCP bic registered
[4294675.003000] NET: Registered protocol family 1
[4294675.003000] NET: Registered protocol family 8
[4294675.003000] NET: Registered protocol family 20
[4294675.003000] Using IPI Shortcut mode
[4294675.003000] ACPI wakeup devices:
[4294675.003000] LANC PS2K PS2M
[4294675.003000] ACPI: (supports S0 S3 S4 S5)
[4294675.003000] Freeing unused kernel memory: 288k freed
[4294675.031000] input: AT Translated Set 2 keyboard as /class/input/input0
[4294675.097000] vga16fb: initializing
[4294675.097000] vga16fb: mapped to 0xc00a0000
[4294675.219000] Console: switching to colour frame buffer device 80x25
[4294675.219000] fb0: VGA16 VGA frame buffer device
[4294676.341000] Capability LSM initialized
[4294676.403000] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[4294676.403000] ACPI: Processor [CPU0] (supports 8 throttling states)
[4294676.421000] ACPI: Thermal Zone [TZ01] (52 C)
[4294676.432000] ACPI: Thermal Zone [TZ02] (0 C)
[4294677.180000] ICH7: IDE controller at PCI slot 0000:00:1f.1
[4294677.180000] ACPI: PCI Interrupt 0000:00:1f.1[B] -> GSI 19 (level,
low) -> IRQ 225
[4294677.180000] ICH7: chipset revision 1
[4294677.180000] ICH7: not 100% native mode: will probe irqs later
[4294677.180000] ide0: BM-DMA at 0x1810-0x1817, BIOS settings:
hda:DMA, hdb:pio
[4294677.180000] Probing IDE interface ide0...
[4294677.852000] hda: HL-DT-ST DVDRAM GSA-4084N, ATAPI CD/DVD-ROM drive
[4294678.158000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294678.176000] hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB
Cache, DMA
[4294678.176000] Uniform CD-ROM driver Revision: 3.20
[4294678.555000] SCSI subsystem initialized
[4294678.557000] ACPI: bus type scsi registered
[4294678.557000] libata version 1.20 loaded.
[4294678.560000] ahci 0000:00:1f.2: version 1.2
[4294678.560000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level,
low) -> IRQ 225
[4294682.872000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[4294682.872000] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5
Gbps 0x5 impl SATA mode
[4294682.872000] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum
part
[4294682.872000] ata1: SATA max UDMA/133 cmd 0xF8886500 ctl 0x0 bmdma
0x0 irq 233
[4294682.872000] ata2: SATA max UDMA/133 cmd 0xF8886580 ctl 0x0 bmdma
0x0 irq 233
[4294682.872000] ata3: SATA max UDMA/133 cmd 0xF8886600 ctl 0x0 bmdma
0x0 irq 233
[4294682.872000] ata4: SATA max UDMA/133 cmd 0xF8886680 ctl 0x0 bmdma
0x0 irq 233
[4294683.076000] ata1: dev 0 cfg 00:0c5a 49:2f00 82:3069 83:7c09 84:6003
85:3069 86:3c09 87:6003 88:203f 93:0000
[4294683.076000] ata1: dev 0 ATA-7, max UDMA/100, 234441648 sectors: LBA48
[4294683.076000] sata_get_dev_handle: SATA dev addr=0x1f0002,
handle=0xdfff3860
[4294683.135000] ata1: dev 0 configured for UDMA/100
[4294683.135000] sata_get_dev_handle: SATA dev addr=0x1f0002,
handle=0xdfff3860
[4294683.137000] scsi0 : ahci
[4294683.339000] ata2: no device found (phy stat 00000000)
[4294683.339000] scsi1 : ahci
[4294683.541000] ata3: no device found (phy stat 00000000)
[4294683.541000] scsi2 : ahci
[4294683.743000] ata4: no device found (phy stat 00000000)
[4294683.743000] scsi3 : ahci
[4294683.743000] Vendor: ATA Model: ST9120821AS Rev: 3.05
[4294683.743000] Type: Direct-Access ANSI SCSI
revision: 05
[4294683.755000] Driver 'sd' needs updating - please use bus_type methods
[4294683.756000] SCSI device sda: 234441648 512-byte hdwr sectors
(120034 MB)
[4294683.756000] SCSI device sda: drive cache: write back
[4294683.761000] SCSI device sda: 234441648 512-byte hdwr sectors
(120034 MB)
[4294683.761000] SCSI device sda: drive cache: write back
[4294683.761000] sda: sda1 sda2 sda3
[4294684.000000] sd 0:0:0:0: Attached scsi disk sda
[4294684.375000] usbcore: registered new driver usbfs
[4294684.376000] usbcore: registered new driver hub
[4294684.378000] USB Universal Host Controller Interface driver v2.3
[4294684.379000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level,
low) -> IRQ 50
[4294684.379000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[4294684.379000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[4294684.381000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 1
[4294684.381000] uhci_hcd 0000:00:1d.0: irq 50, io base 0x00001820
[4294684.383000] hub 1-0:1.0: USB hub found
[4294684.383000] hub 1-0:1.0: 2 ports detected
[4294684.484000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level,
low) -> IRQ 225
[4294684.484000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[4294684.484000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[4294684.484000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned
bus number 2
[4294684.484000] uhci_hcd 0000:00:1d.1: irq 225, io base 0x00001840
[4294684.484000] hub 2-0:1.0: USB hub found
[4294684.484000] hub 2-0:1.0: 2 ports detected
[4294684.513000] ieee1394: Initialized config rom entry `ip1394'
[4294684.585000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level,
low) -> IRQ 185
[4294684.585000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[4294684.585000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[4294684.585000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned
bus number 3
[4294684.585000] uhci_hcd 0000:00:1d.2: irq 185, io base 0x00001860
[4294684.585000] hub 3-0:1.0: USB hub found
[4294684.585000] hub 3-0:1.0: 2 ports detected
[4294684.686000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level,
low) -> IRQ 177
[4294684.686000] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[4294684.686000] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[4294684.686000] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned
bus number 4
[4294684.686000] uhci_hcd 0000:00:1d.3: irq 177, io base 0x00001880
[4294684.687000] hub 4-0:1.0: USB hub found
[4294684.687000] hub 4-0:1.0: 2 ports detected
[4294684.792000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level,
low) -> IRQ 50
[4294684.792000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[4294684.792000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[4294684.792000] ehci_hcd 0000:00:1d.7: debug port 1
[4294684.792000] PCI: cache line size of 32 is not supported by device
0000:00:1d.7
[4294684.792000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned
bus number 5
[4294684.792000] ehci_hcd 0000:00:1d.7: irq 50, io mem 0xd0544000
[4294684.796000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00,
driver 10 Dec 2004
[4294684.796000] hub 5-0:1.0: USB hub found
[4294684.796000] hub 5-0:1.0: 8 ports detected
[4294684.898000] ohci1394: $Rev: 1313 $ Ben Collins <bcollins at debian.org>
[4294684.898000] ACPI: PCI Interrupt 0000:08:06.1[B] -> GSI 19 (level,
low) -> IRQ 225
[4294684.948000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[225]
MMIO=[d0007000-d00077ff] Max Packet=[2048]
[4294685.004000] Probing IDE interface ide1...
[4294686.204000] ieee1394: Host added: ID:BUS[0-00:1023]
GUID[663f0200cc054084]
[4294687.572000] ISO 9660 Extensions: Microsoft Joliet Level 3
[4294687.653000] ISO 9660 Extensions: RRIP_1991A
[4294687.703000] loop: loaded (max 8 devices)
[4294687.720000] Registering unionfs 1.1.2
[4294687.805000] squashfs: version 3.0prerelease (2006/1/24) Phillip Lougher
[4294732.680000] e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI
[4294732.680000] e100: Copyright(c) 1999-2005 Intel Corporation
[4294732.680000] ACPI: PCI Interrupt 0000:08:08.0[A] -> GSI 20 (level,
low) -> IRQ 58
[4294732.715000] e100: eth0: e100_probe: addr 0xd0006000, irq 58, MAC
addr 00:16:D4:0A:E0:48
[4294744.953000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[4294746.045000] NET: Registered protocol family 17
[4294746.860000] Linux agpgart interface v0.101 (c) Dave Jones
[4294746.898000] agpgart: Detected an Intel 945GM Chipset.
[4294746.899000] agpgart: Detected 7932K stolen memory.
[4294746.919000] agpgart: AGP aperture is 256M @ 0xc0000000
[4294747.610000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294747.717000] hw_random hardware driver 1.0.0 loaded
[4294748.094000] shpchp: Standard Hot Plug PCI Controller Driver
version: 0.4
[4294748.160000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level,
low) -> IRQ 66
[4294748.160000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[4294749.137000] Real Time Clock Driver v1.12
[4294749.286000] ACPI: PCI Interrupt 0000:08:06.0[A] -> GSI 18 (level,
low) -> IRQ 185
[4294749.286000] Yenta: CardBus bridge found at 0000:08:06.0 [103c:30a5]
[4294749.286000] Yenta: Enabling burst memory read transactions
[4294749.286000] Yenta: Using INTVAL to route CSC interrupts to PCI
[4294749.286000] Yenta: Routing CardBus interrupts to ISA
[4294749.286000] Yenta TI: socket 0000:08:06.0, mfunc 0x01aa1b22, devctl
0x64
[4294749.946000] Yenta: ISA IRQ mask 0x0cf8, PCI irq 185
[4294749.946000] Socket status: 30000006
[4294749.946000] Yenta: Raising subordinate bus# of parent bus (#08)
from #09 to #0c
[4294749.946000] pcmcia: parent PCI bridge I/O window: 0x2000 - 0x2fff
[4294749.946000] cs: IO port probe 0x2000-0x2fff: clean.
[4294749.947000] pcmcia: parent PCI bridge Memory window: 0xd0000000 -
0xd00fffff
[4294749.947000] pcmcia: parent PCI bridge Memory window: 0x50000000 -
0x51ffffff
[4294750.133000] sdhci: Secure Digital Host Controller Interface driver,
0.10
[4294750.133000] sdhci: Copyright(c) Pierre Ossman
[4294750.312000] ACPI: PCI Interrupt 0000:08:06.3[D] -> GSI 20 (level,
low) -> IRQ 58
[4294750.362000] sdhci: ============== REGISTER DUMP ==============
[4294750.362000] sdhci: Sys addr: 0x00000000 | Version: 0x00008900
[4294750.362000] sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
[4294750.362000] sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
[4294750.362000] sdhci: Present: 0x000a0000 | Host ctl: 0x00000000
[4294750.362000] sdhci: Power: 0x00000000 | Blk gap: 0x00000000
[4294750.362000] sdhci: Walk up: 0x00000000 | Clock: 0x00000000
[4294750.362000] sdhci: Timeout: 0x0000000e | Int stat: 0x00000000
[4294750.362000] sdhci: Int enab: 0x11ff00cf | Sig enab: 0x11ff00cf
[4294750.362000] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[4294750.362000] sdhci: Caps: 0x018030b0 | Max curr: 0x00000000
[4294750.362000] sdhci: ===========================================
[4294750.413000] mmc0: SDHCI at 0xd0007800 irq 58 DMA
[4294750.559000] ieee80211_1_1_13_crypt: registered algorithm 'NULL'
[4294750.561000] ieee80211_1_1_13: 802.11 data/management/control stack,
1.1.13
[4294750.561000] ieee80211_1_1_13: Copyright (C) 2004-2005 Intel
Corporation <jketreno at linux.intel.com>
[4294750.635000] ieee80211_crypt: registered algorithm 'NULL'
[4294750.685000] ieee80211: 802.11 data/management/control stack, git-1.1.7
[4294750.685000] ieee80211: Copyright (C) 2004-2005 Intel Corporation
<jketreno at linux.intel.com>
[4294751.099000] ipw3945: Intel(R) PRO/Wireless 3945 Network Connection
driver for Linux, 1.0.3m
[4294751.099000] ipw3945: Copyright(c) 2003-2006 Intel Corporation
[4294751.099000] ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 18 (level,
low) -> IRQ 185
[4294751.099000] PCI: Setting latency timer of device 0000:06:00.0 to 64
[4294751.099000] ipw3945: Detected Intel PRO/Wireless 3945ABG Network
Connection
[4294751.575000] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1,
caps: 0xa04713/0x200000
[4294751.642000] input: SynPS/2 Synaptics TouchPad as /class/input/input1
[4294752.737000] ts: Compaq touchscreen protocol output
[4294752.780000] ipw3945: Detected geography ABG (11 802.11bg channels,
13 802.11a channels)
[4294752.881000] cs: IO port probe 0x100-0x3af: clean.
[4294752.883000] cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
[4294752.884000] cs: IO port probe 0x820-0x8ff: clean.
[4294752.885000] cs: IO port probe 0xc00-0xcf7: clean.
[4294752.886000] cs: IO port probe 0xa00-0xaff: clean.
[4294756.701000] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294756.701000] md: bitmap version 4.39
[4294757.259000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised:
dm-devel at redhat.com
[4294772.201000] ACPI: AC Adapter [ACAD] (on-line)
[4294772.328000] ACPI: Battery Slot [BAT1] (battery absent)
[4294772.432000] ACPI: Power Button (FF) [PWRF]
[4294772.432000] ACPI: Lid Switch [LID]
[4294772.432000] ACPI: Power Button (CM) [PWRB]
[4294772.630000] ibm_acpi: ec object not found
[4294772.669000] pcc_acpi: loading...
[4294772.826000] ACPI: Video Device [VGA] (multi-head: yes rom: no
post: no)
[4294772.826000] ACPI: Video Device [GFX0] (multi-head: yes rom: no
post: no)
[4294780.469000] lp: driver loaded but no devices found
[4294780.646000] ppdev: user-space parallel port driver
[4294781.914000] apm: BIOS not found.
[4294787.103000] Bluetooth: Core ver 2.8
[4294787.103000] NET: Registered protocol family 31
[4294787.103000] Bluetooth: HCI device and connection manager initialized
[4294787.103000] Bluetooth: HCI socket layer initialized
[4294787.318000] Bluetooth: L2CAP ver 2.8
[4294787.318000] Bluetooth: L2CAP socket layer initialized
[4294787.333000] Bluetooth: RFCOMM socket layer initialized
[4294787.333000] Bluetooth: RFCOMM TTY layer initialized
[4294787.333000] Bluetooth: RFCOMM ver 1.7
[4294790.828000] [drm] Initialized drm 1.0.1 20051102
[4294791.083000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level,
low) -> IRQ 177
[4294791.084000] [drm] Initialized i915 1.4.0 20060119 on minor 0
[4295015.119000] usb 5-4: new high speed USB device using ehci_hcd and
address 2
[4295019.515000] Initializing USB Mass Storage driver...
[4295019.515000] scsi4 : SCSI emulation for USB Mass Storage devices
[4295019.515000] usb-storage: device found at 2
[4295019.515000] usb-storage: waiting for device to settle before scanning
[4295019.515000] usbcore: registered new driver usb-storage
[4295019.515000] USB Mass Storage support registered.
[4295024.515000] Vendor: I0MEGA Model: Mini256MB*IOM2D5 Rev: 2.00
[4295024.515000] Type: Direct-Access ANSI SCSI
revision: 00
[4295024.517000] SCSI device sdb: 504832 512-byte hdwr sectors (258 MB)
[4295024.518000] sdb: Write Protect is off
[4295024.518000] sdb: Mode Sense: 0b 00 00 00
[4295024.518000] sdb: assuming drive cache: write through
[4295024.520000] SCSI device sdb: 504832 512-byte hdwr sectors (258 MB)
[4295024.521000] sdb: Write Protect is off
[4295024.521000] sdb: Mode Sense: 0b 00 00 00
[4295024.521000] sdb: assuming drive cache: write through
[4295024.521000] sdb: sdb1
[4295024.522000] sd 4:0:0:0: Attached scsi removable disk sdb
[4295024.522000] sd 4:0:0:0: Attached scsi generic sg1 type 0
[4295024.523000] usb-storage: device scan complete
[4295044.463000] UDF-fs: No partition found (1)
[4295044.492000] UDF-fs: No partition found (1)
[4295044.558000] Unable to identify CD-ROM format.
[4295044.613000] Unable to identify CD-ROM format.
[4295044.793000] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
[4295746.163000] usb 5-4: USB disconnect, address 2
[4295746.163000] sd 4:0:0:0: rejecting I/O to device being removed
[4295746.163000] Buffer I/O error on device sdb1, logical block 501
[4295746.163000] lost page write due to I/O error on sdb1
[4295746.163000] sd 4:0:0:0: rejecting I/O to device being removed
[4295746.163000] Buffer I/O error on device sdb1, logical block 495
[4295746.163000] lost page write due to I/O error on sdb1
[4296752.119000] usb 5-4: new high speed USB device using ehci_hcd and
address 3
[4296752.234000] scsi5 : SCSI emulation for USB Mass Storage devices
[4296752.234000] usb-storage: device found at 3
[4296752.234000] usb-storage: waiting for device to settle before scanning
[4296757.234000] Vendor: I0MEGA Model: Mini256MB*IOM2D5 Rev: 2.00
[4296757.234000] Type: Direct-Access ANSI SCSI
revision: 00
[4296757.236000] SCSI device sdc: 504832 512-byte hdwr sectors (258 MB)
[4296757.237000] sdc: Write Protect is off
[4296757.237000] sdc: Mode Sense: 0b 00 00 00
[4296757.237000] sdc: assuming drive cache: write through
[4296757.239000] SCSI device sdc: 504832 512-byte hdwr sectors (258 MB)
[4296757.240000] sdc: Write Protect is off
[4296757.240000] sdc: Mode Sense: 0b 00 00 00
[4296757.240000] sdc: assuming drive cache: write through
[4296757.240000] sdc: sdc1
[4296757.241000] sd 5:0:0:0: Attached scsi removable disk sdc
[4296757.241000] sd 5:0:0:0: Attached scsi generic sg1 type 0
[4296757.242000] usb-storage: device scan complete
[4296759.213000] UDF-fs: No partition found (1)
[4296759.245000] UDF-fs: No partition found (1)
[4296759.296000] Unable to identify CD-ROM format.
[4296759.345000] Unable to identify CD-ROM format.
[4296759.351000] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
[4297048.413000] usb 5-4: USB disconnect, address 3
[4297335.869000] usb 5-6: new high speed USB device using ehci_hcd and
address 4
[4297335.984000] scsi6 : SCSI emulation for USB Mass Storage devices
[4297335.984000] usb-storage: device found at 4
[4297335.984000] usb-storage: waiting for device to settle before scanning
[4297340.984000] Vendor: I0MEGA Model: Mini256MB*IOM2D5 Rev: 2.00
[4297340.984000] Type: Direct-Access ANSI SCSI
revision: 00
[4297340.986000] SCSI device sdb: 504832 512-byte hdwr sectors (258 MB)
[4297340.987000] sdb: Write Protect is off
[4297340.987000] sdb: Mode Sense: 0b 00 00 00
[4297340.987000] sdb: assuming drive cache: write through
[4297340.989000] SCSI device sdb: 504832 512-byte hdwr sectors (258 MB)
[4297340.990000] sdb: Write Protect is off
[4297340.990000] sdb: Mode Sense: 0b 00 00 00
[4297340.990000] sdb: assuming drive cache: write through
[4297340.990000] sdb: sdb1
[4297340.991000] sd 6:0:0:0: Attached scsi removable disk sdb
[4297340.991000] sd 6:0:0:0: Attached scsi generic sg1 type 0
[4297340.992000] usb-storage: device scan complete
[4297342.865000] UDF-fs: No partition found (1)
[4297342.889000] UDF-fs: No partition found (1)
[4297342.937000] Unable to identify CD-ROM format.
[4297342.985000] Unable to identify CD-ROM format.
[4297342.992000] FAT: utf8 is not a recommended IO charset for FAT
filesystems, filesystem will be case sensitive!
_______________________________________________
nflug mailing list
nflug at nflug.org
http://www.nflug.org/mailman/listinfo/nflug
More information about the nflug
mailing list