New User

Cyber Source peter at thecybersource.com
Fri Jun 27 23:09:21 EDT 2003


ok, lets not loose our heads here......
I would remove any references to eth0 in your /etc/modules.conf file and
then reboot the machine (you could run kudzu instead but), it should
refind the network card and ask to configure, do the configure but do
NOT migrate the existing networking. That hopefully should fix the
networking issue.
Then, in your BIOS boot sequence, just make sure the onboard ide
controllers are not in the choices.
Try those and aside from this stuff, if your installs were done with
downloaded ISO's, did you do any md5sum checks to make sure they didnt
get corrupted? Did the install go ok? Seems like you have many problems.
Try those and let me know.
On Fri, 2003-06-27 at 22:46, Joe Isom wrote:

> Oooohhhhhhhooo this is frustrating.  When I read your comment about
> setting the BIOS for SCSI, I thought to myself, "Why of course!"  I was
> all excited, but then when I got into my BIOS, believe it or not, there
> is no setting to account for a SCSI device.  And it's not as if I have
> an old computer.  This is a Dell Dimension 4100 with an 800mHz Pentium. 
> Before I started monkeying around with this project I did flash my BIOS
> with the latest version available -- A11.
> 
> Also, I deleted the existing device profile in network configurations
> and reinstalled my ethernet device, making sure I set the host name as
> localhost.localdomain.  This brings up another issue.  When I launch
> neat, I get a warning message (yellow triangle w/exclamation point) that
> states:
> 
> "eth0 has an alias to module CDC in modules.conf,
> instead of currently loaded module CDC Ethernet Class!"
> 
> What's this telling me?
> 
> But I was getting this all along since my first installation attempt.
> (This makes about the 5th time I've deleted and reinstalled my ethernet
> settings, hoping to get things right.)
> 
> I'm still getting the "Could not look up internet address for . . ."
> when I log in, except that "dhcp-124-6" has been replaced by
> "localhost.localdomain"
> 
> Also, I believe it was Mike that mentioned that I should delete the
> firewall from RedHat.  Since I can't seem to change the firewall
> settings from "High security," deleting the entire firewall sounds good
> right now.  How do I do that?
> 
> You know, I just had to have this 160 GB drive I found at Sams to
> replace the original equipment 20 GB drive running Windows ME.  But I
> never thought to check to see if it was compatible with my existing
> BIOS.  I thought I was going to be able to install it alongside my 20 GB
> drive using the onboard IDE channels, and then copy over whatever files
> I wanted to keep -- even have a dual boot system!  But then, after I got
> it home, that's when I learned why that nice 48-bit LBA supported
> controller card was included.  I wish now that I had a <137 GB drive.
> 
> Again, thank you for taking your time to try and help me figure this
> out.  I really appreciate it.
> 
> Joe Isom
> 
> 
> On Thu, 2003-06-26 at 23:18, Cyber Source wrote:
> > Ok, I other thing, lol. Check the boot order in your BIOS and there
> > should be a selection for SCSI, put that before any reference to the
> > onboard IDE controller, this will tell the BIOS that it needs to look
> > beyond it's own controller(s) for a boot record.
> > On Thu, 2003-06-26 at 23:08, Cyber Source wrote: 
> > > One other note on that, take a look at the example of my lilo.conf
> > > file, lilo will always want to write to the first hard drive,
> > > usually /dev/hda but if that is not possible, like in your case or
> > > in mine below, you need to tell it what drive is first, hence, the
> > > bios=0x80 reference, that tells lilo that that is the first hard
> > > drive and where to write the master boot record too. In my case, I
> > > wanted it on my scsi hard drive, so I put that first and the put my
> > > windows drive (/dev/hdb) and told lilo that it is my second drive
> > > but not 0x81 instead at 0x82 because /dev/hda is actually on the
> > > system but I only mount it when needed. Hope this helps....
> > > 
> > > On Thu, 2003-06-26 at 22:56, Cyber Source wrote: 
> > > > OK, sounds like you've got a few problems. First, from a command
> > > > prompt, run the command neat, then adjust your network settings
> > > > accordingly. Your 127.0.0.1 address should not be hosting to
> > > > adelphia so remove the adelphia stuff and put in
> > > > localhost.localdomain .
> > > > You need to see how your harddrive is being recognized, run the
> > > > command dmesg and see what your hard drive is, it is probably
> > > > something like /dev/hde since it's on a seperate controller. There
> > > > are a bunch of options that can be put in the lilo.conf file, most
> > > > importantly the map-drive= line, to give you an idea of the
> > > > seperate commands on a dual boot/multi hard drive system, I will
> > > > include a copy of my /etc/lilo.conf file, if you change that, run
> > > > the lilo command again and you can probably do away with the
> > > > floppy, One other VERY important note, some systems cant handle
> > > > the linear geometry, change that to lba32 if so,
> > > > 
> > > > prompt
> > > > timeout=50
> > > > default=RedHat
> > > > boot=/dev/sda
> > > > disk=/dev/sda bios=0x80
> > > > disk=/dev/hdb bios=0x82
> > > > map=/boot/map
> > > > install=/boot/boot.b
> > > > message=/boot/message
> > > > linear
> > > > 
> > > > image=/boot/vmlinuz-2.4.18-14
> > > >         label=RedHat
> > > >         initrd=/boot/initrd-2.4.18-14.img
> > > >         read-only
> > > >         append="hdc=ide-scsi root=LABEL=/"
> > > > other=/dev/hdb1
> > > >         label=Windows
> > > >         table=/dev/hdb
> > > >         map-drive=0x80
> > > >         to=0x82
> > > >         map-drive=0x82
> > > >         to=0x80
> > > > 
> > > > On Thu, 2003-06-26 at 22:32, Joe Isom wrote: 
> > > > > I used the command Mark gave me, and the settings for iptables look as
> > > > > you say it should.  But nothing changed with respect to my inability to
> > > > > go anywhere but Redhat.com.  And it is the Redhat.com site as opposed to
> > > > > any built-in help files.  For example, I was able to sign up for the
> > > > > demo RHN account and have it query my system for available updates.
> > > > > 
> > > > > Also, I attempted to edit my etc/hosts file.  It now looks like this:
> > > > > 
> > > > > # Do not remove the following line, or various programs
> > > > > # that require network functionality will fail.
> > > > > 127.0.0.1	GCPL301.buf.adelphia.net	localhost
> > > > > 
> > > > > That host name above is what I got from the Host Name field in ipconfig
> > > > > when I was running Windows.  I'm not sure about that IP address though. 
> > > > > Does it look like I set it up correctly?  I still get the "Welcome to
> > > > > dhcp-124-6" at the login screen, and the "Could not look up internet
> > > > > address . . ." message when logging in despite making this change.
> > > > > 
> > > > > Another problem that I didn't mention before is that I can only boot
> > > > > from a floppy.  I'm not sure exactly why, but I guess it is because my
> > > > > BIOS doesn't know how to look for the hard drive as a bootable device. 
> > > > > And that may be because my drive is connected through an ultra ATA
> > > > > controller card being that it is too large for my system BIOS.  When I
> > > > > go into my BIOS setup, it simply shows my onboard IDE 1 channels as
> > > > > being empty (which they are) and my DVD and CD as installed in the IDE 2
> > > > > channels.  It can't see the controller card or the two drives attached
> > > > > to it.  However, when the machine boots, I can see when the BIOS on the
> > > > > controller card runs and detects the two drives attached to it.
> > > > > 
> > > > > Anyway, I was wondering if there might be a setting on the floppy that
> > > > > is giving me trouble.
> > > > > 
> > > > > Again, I'm most appreciative of all your help.
> > > > > 
> > > > > Joe Isom
> > > > > 
> > > > > 
> > > > > On Thu, 26 Jun 2003, John Seth wrote:
> > > > > 
> > > > > > cd /etc/rc.d/rc5.d/
> > > > > > ls
> > > > > > (look for something named S##iptables, mine is S08iptables)
> > > > > > mv S08iptables K08iptables
> > > > > > (change the "S" to a "K")
> > > > > > ls
> > > > > 
> > > > > Actually, use chkconfig again:
> > > > > 
> > > > > chkconfig --level 345 iptables off
> > > > > 
> > > > > Then you don't have to mess around with the symlinks & Ks & Ss manually.
> > > > > 
> > > > > >
> > > > > > There should now be K##iptables.  Now iptables will not start on
> > > > > bootup.
> > > > > >  Using 'setup' RedHat will always try to get you to reset your
> > > > > firewall
> > > > > > to "High"... it doesn't reflect any changes you made, at least not on
> > > > > my
> > > > > > RH 9 system (which I'm using now).
> > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > -- 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > 
> > > > Cyber Source <peter at thecybersource.com>
> > > 
> > > 
> > > 
> > > 
> > > 
> > > -- 
> > > 
> > > 
> > > 
> > > Cyber Source <peter at thecybersource.com>
> > 
> > 
> > -- 
> > 
> > Cyber Source <peter at thecybersource.com>
> > 
> > 

-- 
Cyber Source <peter at thecybersource.com>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.nflug.org/pipermail/nflug/attachments/20030628/26a75da3/attachment-0001.html


More information about the nflug mailing list